Conceptual solutions for the manufacture of cargo wagon bearing systems from composites (Part 1): monograph

Abstract

The monograph will be useful for scientists, designers, engineers whose activities are related to the improvement of technical, economic and operational indicators of non-traction rolling stock at various stages of its life cycle.

In particular, the issue of the possibility and expediency of introducing various types of constructive hierarchy of components in the design of wagons. What can happen when creating new models of them or modernizing existing ones.

To date, the traditional approach to creating a structure of freight wagons from steel has almost completely exhausted the potential for improving their technical, economic and operational indicators. At the same time, the experience of the development of composite materials and technologies for their creation in other branches of light and heavy engineering and instrument building indicates the prospect of deploying relevant research and development works on the use of such materials in railcar construction.

The purpose of the monograph is to highlight the results obtained from the creation of conceptual solutions for the manufacture of component load-carrying systems of freight wagons from composites. The book also presents the results of previous works of a theoretical and practical nature. In particular, given. Analysis of the constructive perfection of truck wagons of the modern domestic vehicle by type. Features of calculations of  conceptual solutions for manufacturing non-sowing systems cargo wagons made of composites. Concepts for freight wagons made of composites.

The book can be used as a study guide for the preparation of bachelors, masters, doctors of philosophy and doctors of sciences in various specialties of transport mechanics. Including from specialties: railway transport, transport technologies, mechanical engineering, materials science and others.

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

^{This monograph is recommended for printing by the Science Council of Volodymyr Dahl East Ukrainian National University (protocol No 03 dd 27.10.2023).}

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

^REVIEWERS:

^{MASLIYEV Vyacheslav - Doctor of Technical Sciences, Professor, Department of Electric Transport and Heat Engineering, National Technical University «Kharkiv Polytechnic Institute», Ukraine}

^{SAPRONOVA Svitlana - Professor, Doctor of Technical Sciences, Department of cars and carriage facilities, State University of Infrastructure and Technologies, Ukraine}

^{TKACHENKO Viktor - Professor, Doctor of Technical Sciences, Department of Traction Rolling Stock of Railways, State University of Infrastructure and Technologies, Ukraine}

^{USTENKO Oleksander - Professor, Doctor of Technical Sciences, Dean of the Faculty of Mechanics and Energy, Ukrainian State University of Railway Transport, Ukraine.}

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

CONTENTS:

INTRDUCTION

SECTION 1. ANALYSIS OF THE CONSTRUCTIVE PERFECTION OF TRUCK WAGONS OF THE MODERN DOMESTIC VEHICLE BY TYPE
1.1 Design features of semi-wagons
1.2 Design features of covered wagons
1.3 Design features of wagons of platform wagons
1.4 Design features of tank wagons
1.5 Design features of hopper wagons for transportation of hot pellets and sinter

SECTION 2. FEATURES OF CALCULATIONS OF CONCEPTUAL SOLUTIONS FOR MANUFACTURING NON-SOWING SYSTEMS CARGO WAGONS MADE OF COMPOSITES
2.1 Wear in mechanisms and mechanical efficiency
2.2 Strangth calculations for deformations “tension-compression”
2.3 Mechanical characteristics of materials
2.4 Strangth calculations for deformation “shear”
2.5 Geometric characteristics of plane sections
2.6 Strangth calculations in deformation “torsion”
2.7 Strangth calculations under deformations “flexure”
2.8 Basics of theory of stressed and deformed state
2.9 Stability calculations
2.10 Strength of materials at cyclic stresses
2.11 Basic types and characteristics of modern materials
2.12 Production specifications for machine tools
2.13 Analysis of the forces acting on the supporting structure of the flat carin operation
2.14 Classification of rolling stock dimensions
2.15 Determination of the vertical dimensions of the construction outline of the wagon
2.16 Determination of the horizontal dimensions of the construction outlines of the wagon

SECTION 3. CONCEPTS FOR FREIGHT WAGONS MADE OF COMPOSITES
3.1 Railway semi-wagon with a hollow body
3.2 Covered wagon
3.3 Railway tank
3.4 Platform wagon for timber transportation
3.5 Hopper wagon
3.6 Universal covered wagon
3.7 Universal semi-wagon hatch cover
3.8 Universal semi-wagon
3.9 Detachable roof of a semi-wagon
3.10 Railway tank
3.11 Platform wagon for bulk cargo transportation

GENERAL CONCLUSIONS

REFERENCES

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

^{Year of publication: 2023
Language: English
Authors: Fomin O., Fomina A.
Translation: No
Translator: -}

^{Type: E-book
Number of pages: 356
Format: PDF (145 MB)
ISBN: 979-8-89217-814-3
UDC: 629.4.02.001.76}